Simply apply the product and sweep it over the concrete until the excess powder has been disbursed. EXIMO is a waterless powder that's easy to use. This process restores the surface to its original appearance without the need for expensive pressure washing or the use of harsh chemicals. Through a process called bioremediation, microbes in EXIMO breakdown the hydrocarbon chain of petroleum stains deep below the surface into harmless water and CO2. EXIMO is more than a surface cleaner, it’s an all-natural waterless cleaner that uses a time-driven process and nature’s own biochemistry to completely remove tough petroleum stains from concrete. Seek immediate medical attention if symptoms persist.Eximo Waterless Concrete Cleaner for Driveway, Garage, Basement, and Walkway Surfaces, Advanced Stain Remover for Oils and Other Petroleum Stains 36ĮXIMO® cleans oil stains better than pressure washing by working deep into the pores of the concrete, restoring its original luster and clean appearance. Symptoms include an itchy rash, redness, blisters and scaling, or in more severe cases, dropping blood pressure, swelling of the throat and tongue and difficulty breathing. LATEX ALLERGY NOTICE: ABR Waterless Fireplace Cleaner ™ contains latex (a natural fluid produced by the rubber tree) and may cause allergic reactions in some people. Do not pour product down the drain or clean tools in a sink. Dispose of latex film in accordance with local latex paint guidelines. CLEAN UP & DISPOSAL: Dispose of all application tools into the trash. Thin applications of ABR Waterless Fireplace Cleaner ™ may be difficult to remove and may require the use of the ABR Citrus Paint Remover Liquid ®. Allowing the ABR Waterless Fireplace Cleaner ™ to remain on a heavily textured surface for longer may make the removal of the film difficult. NOTE: To ensure the ease of removal, remove from the surface within 3 days of the initial date of application. When film is completely removed and your work area cleaned of all product, your fireplace can be used. Start at the edge and roll up the film as you go, taking care not to tear. Test the thick coat on the edge for complete dryness. The film MUST be completely dry before removal begins. Depending on how much product is in the mortar joints, wait 6-12 hours to remove the film. In very dry climates or on porous surfaces you may find it helpful to agitate a heavily soiled area with a water dampened brush to prevent premature drying. The ABR Waterless Fireplace Cleaner ™ does not require water in its application or removal however, it is not water incompatible. Brush or roll a second coat of ABR Waterless Fireplace Cleaner ™ over the scrubbed area for a uniform thickness to help aid in removal. Work the coating into the surface while wet. The heavy black soot on your fireplace may need to be agitated with a short bristle nylon scrub brush. Thin applications (less than 1/8” thick) may result in difficulties during removal such as premature tearing of the film. This will allow for an easy start to peeling off the dried film. Use a roller with a 4, 7, or 9 x 1/2” knit cover, roll a generous amount of ABR Waterless Fireplace Cleaner ™ on the rest of the surface. Apply a liberal coat about 1/8” thick around the fireplace door. Apply to a dry surface at a consistent temperature of 50☏ or higher. Take extra precautions to protect all wood surfaces and fabric/carpet as this product may stain wood and can not be easily removed from fabric/carpet. Use masking tape to adhere a plastic drop cloth around the base of the fireplace. APPLICATION: Before beginning application, mask off your work area and using drop clothes or plastic sheeting, cover all adjacent surfaces to protect from coating splatter. This is especially important when temperatures are approaching or above 80☏ as the ABR Waterless Fireplace Cleaner ™ may cure in only a few hours. Apply in an inconspicuous location and allow to thoroughly dry, then test the ABR Waterless Fireplace Cleaner ™ for ease of removal and overall results. A test area should be performed before beginning project to ensure product compatibility with your specific surfaces. PREPARATORY WORK: User shall determine the suitability of the product for its intended use and assumes all risk and liability whatsoever in connection therewith.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |